Rocktron Patchmate Loop 8 Floor Instrukcja Użytkownika

1MANUALMay be covered by one or more of the following: U.S. Patents #4538297, 4647876, 4696044, 4745309, 4881047, 4893099, 5124657, 5263091, 5268527,

10Individual LOOP Jacks Descriptions1 IN Jack This is the rst jack in the signal chain. The audio signal will enter the "LOOP" through t

11ConnectionsThis connection diagram shows one way to use the LOOPs in the PatchMate LOOP 8 Floor to connect stompboxes (pedals). Although only two c

12Connections...continued...This connection diagram shows one way to use the LOOPs in the PatchMate LOOP 8 Floor. Although only two connections ar

13This connection diagram shows one way to use the LOOPs in the PatchMate to connect to multiple ef-fects processors. Connections...continued...

141OUT - N.O.RETURN SEND - N.C. INTo RETURNof PatchMateOUT tonext Loop or deviceIN toLoop 1PR E S ETPAR AM ET ERADJ US TFU NC TIO NS EL EC TINP UTLE V

15This connection diagram shows one way to use the LOOPs in the PatchMate to connect two ampliers and select between the two.Connections...continued

16Connections...continued...This connection diagram shows one way to use the PatchMate LOOP 8 Floor's SENDS to change change channels on an am

17Connections...continued...This connection diagram shows one way to use the PatchMate LOOP 8 Floor's buffered connection.

18Connections...continued...This connection diagram shows one way to use the PatchMates buffered connection to connect to two different preamps.

19Connections...continued...This connection diagram shows one way to connect the PatchMate to "MUTE" an effects processor where paralle

2Your PatchMate LOOP 8 Floor has been designed to comply with the following Standards and Directives as set forth by the European Union: Council Dire

20Connections...continued...This connection diagram shows how to connect the PatchMate to a MIDI Controller such as the Rocktron MIDI Mate (use sim

21LOOPS and PRESETS Descriptions- Creating & Storing:The PatchMate LOOP 8 Floor has two basic MODES of operation, LOOP MODE (Default) and PRE-SET

22PRESETS - Selecting, Creating & Storing:To create and store a preset follow these instructions;To select a preset:1 Press and Release the "

23In order to provide the ultimate exibility the operating system has been upgraded.The Patchmate Loop 8 Floor now has two different Preset Recall mo

24Setup your PatchMate LOOP 8 Floor:SETUP MODE: To enter setup mode once you turn the power on you have 3 seconds to press the Store butt

25MIDI Channel Select

263. Once you have pressed the Store switch from step 2, the TOP PANEL SWITCH LEDs [ 1 thru 8 ] will blink twice and the STORE BUTTON will continue to

27MIDI Controller Bank Setup*CANCEL: PRESS SWITCH 6 then PRESS and RELEASE the STORE BUTTON to CANCEL the PROGRAM-MING MODE.Note: If CANCEL is execut

28Preset DumpMIDI PRESET DUMP PROCEDURE: To DUMP or copy presets from your PatchMate LOOP 8 Floor to another PatchMate LOOP 8 Floor, rst connect the

29To link loops in Stereo, follow these instructions1. Turn the PatchMate LOOP 8 Floor "ON", then press and hold the STORE button down until

3PRECAUTIONSNOTE: IT IS VERY IMPORTANT THAT YOU READ THIS SECTION TO PRO-VIDE YEARS OF TROUBLE FREE USE. THIS UNIT REQUIRES CAREFUL HAN-DLING. • All

30SETTING PatchMate USING MIDI PROGRAM CHANGESNow that you have congured your PatchMate LOOP 8 Floor MIDI CHANNEL to the same channel as your midi co

31On the initial reception of this ON state value the target relay will be activated followed by the execu-tion of the delay release timer. Note: When

32Rocktron -A Division of GHS Corporation2813 Wilber AvenueBattle Creek MI 49037USARocktron Phone: 1-(269)-968-3351Email: [email protected]

4IntroductionThe PatchMate LOOP 8 Floor provides 8 discrete Loops all with True Bypass, buffered and non buff-ered signal paths, 128 programmable pres

5 PatchMate LOOP 8 Floor Top Panel1 LOOP Switches These switches are used to turn "on/off" each individual loop. The LED above each switc

66 CHANGES Function In this function switch 8 is used to select if you would like the PatchMate LOOP 8 Floor to respond to MIDI Program changes and

71 ACTIVE Input Jack Plug your guitar into this jack to use the buffered input. This ACTIVE Input Jack is connected to an active buffer that helps

8NOTE: The following example is to illustrate a serial chain of effects and how the Patchmate Loop 8 Floor may be applied. It is not necessary to da

9PatchMate LOOP 8 Floor Back Panel...continued...9 PASSIVE/ACTIVE OUTPUT Jack Use this jack to plug into the next unit in your signal chain or the